Magazine Plug
The 9410 is delivered with a three-shot adapter plug included in the box. This plug limits magazine capacity to two shells in compliance with federal migratory bird (doves are migratory birds) regulations and regulations in some states. If you do not wish to be limited to three shots total — when it is not required by law — you can remove the adapter plug. When removing the plug, be certain there are no shells in the magazine or chamber and keep the barrel and magazine pointed in a safe direction at all times. Remember, the plug and magazine cap are under spring pressure, so care must be taken for safe removal. Always point the end of the magazine away from your face and in a safe direction. Never look directly down into the cap end of the open magazine. Always wear eye protection when removing and installing the magazine’s three-shot plug. If you misplace or break the adapter included with your Model 9410, contact our parts department.

Adapter Removal, Model 9410 Traditional—
1. Place the safety in the “on safe” position and fully unload your Model 9410.
2. Loosen and remove the magazine end cap retaining screw located on the underside of the forward end of the magazine tube.
3. Carefully remove the magazine end cap from the magazine. Remember, it is under spring load.
4. As the spring rises out of the magazine tube, it will lift the three-shot adapter with it.
5. Remove the three-shot adapter from the spring.
6. Replace the magazine end cap, pushing the spring back down into the magazine tube.
7. Replace the magazine cap retaining screw.

Adapter Installation Model 9410 Traditional—
1. Place the safety in the “on safe” position and fully unload your Model 9410.
2. Loosen and remove the magazine end cap retaining screw located on the underside of the forward end of the magazine tube.
3. Carefully remove the magazine end cap from the magazine. Remember, it is under spring load.
4. The spring will rise out of the magazine tube.
5. Place the three shot adapter inside the magazine spring coils with the flared end of the adapter resting on the top coil.
6. Replace the magazine end cap, pushing the spring and adapter back down into the magazine tube.
7. Replace the magazine cap retaining screw.

Adapter Removal, Model 9410 Packer — 1. Place the safety in the “on safe” position and fully unload your Model 9410.
2. Remove the two screws on the front of forearm cap using a standard screwdriver.
3. Pass a small screwdriver through the hole in the sling post found on the end of the magazine tube. Turn the post counterclockwise to loosen the post.
4. Slide forearm cap forward on magazine tube. Carefully remove the magazine end cap from the magazine by tilting the magazine tube away from the barrel enough to clear the sling post mounting stud on the barrel. Remember, magazine cap is under spring load.
5. As the spring rises out of the magazine tube, it will lift the three-shot adapter with it. Remove the three-shot adapter from the spring.
6. Replace magazine end cap, pushing the spring back down into the magazine tube. Be sure to install the end cap with the flat spot around the sling post mounting stud hole facing away from the barrel.
7. Before tilting the magazine back in place on the sling post mounting stud, note the two different sized holes in the end of the magazine tube. The larger hole must face away from the barrel.
8. Replace magazine tube onto sling post mounting stud.
9. Replace sling post through magazine tube and end cap. Carefully install sling post making sure the largest part of the sling post is properly installed and passes through hole in magazine tube. Failure to do so will cause damage to magazine tube.

Adapter Installation Model 9410 Packer —
1. Place the safety in the “on safe” position and fully unload your Model 9410.
2. Remove the two screws on the front of forearm cap using a standard screwdriver.
3. Pass a small screwdriver through the hole in the sling post found on the end of the magazine tube. Turn the post counter clockwise to loosen the post.
4. Slide forearm cap forward on magazine tube. Carefully remove the magazine end cap from the magazine by tilting the magazine tube away from the barrel enough to clear the sling post mounting stud on the barrel. Remember, magazine is under spring load.
5. The spring will rise out of the magazine tube. Place the three shot adapter inside the magazine spring coils with the flared end of the adapter resting on the top coil.
6. Replace magazine end cap, pushing the spring and adapter back down into the magazine tube. Be sure to install the end cap with the flat spot around the sling post mounting stud hole facing away from the barrel.
7. Before tilting the magazine back in place on the sling post mounting stud, note the two different sized holes in the end of the magazine tube.The larger hole must face away from the barrel.
8. Replace magazine tube onto sling post mounting stud.
9. Replace sling post through magazine tube and end cap. Carefully install sling post making sure the largest part of sling post is properly installed and passes through the hole in the magazine tube. Failure to do so will cause damage to the magazine tube.
10. Return forearm cap to original location and secure forearm cap with screws.